Kia Optima Manuals

Kia Forte: Adjustment - Front Door - Body (Interior and Exterior) - Kia Forte TD 2014-2018 Service ManualKia Forte: Adjustment

Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Body (Interior and Exterior) / Front Door / Adjustment

Glass Adjustment
  
•
Check the glass run channel for damage or deterioration, and replace them if necessary.
1.
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
2.
Remove the front door window glass mounting hole plug.
3.
Carefully move the front door window glass (A) until the glass mounting bolts are visible, then loosen them.
(4Door, 5Door)

(2Door)
4.
Check that the glass moves smoothly.
Door Striker Adjustment
  
•
Make sure the door latches securely without slamming it. If necessary adjust the striker (A): The striker nuts are fixed. The striker can be fine adjusted up or down, and in or out.
1.
Loosen the screws (B) just enough for the striker to move.
Tightening torque :
(B) : 16.7 ~ 25.5 N.m (1.7 ~ 2.6 kgf.m, 12.3 ~ 18.8 lb-ft)

2.
Tap on the striker with a plastic hammer to adjust the striker. The striker will not move much, but will give some adjustment.
3.
Hold the outer handle out, and push the door against the body to be sure the striker allows a flush fit. If the door latches properly, tighten the screws and recheck.
Door Position Adjustment
  
•
After installing the door, check for a flush fit with the body, then check for equal gaps between the front, rear, and bottom, door edges and the body. Check that the door and body edges are parallel. Before adjusting, replace the mounting bolts.
1.
Check that the door and body edges are parallel.
2.
Place the vehicle on a firm, level surface when adjusting the doors.
3.
Adjust at the hinges (A) :
A.
Loosen the door mounting bolts slightly, and move the door in or out until it aligns flush with the body.
B.
Loosen the hinge mounting bolts slightly, and move the door backward or forward, up or down as necessary to equalize the gaps.
C.
Place a shop towel on the jack to prevent damage to the door when adjusting the door.
Tightening torque :
(B) : 21.6 ~ 26.5 N.m (2.2 ~ 2.7 kgf.m, 15.9 ~ 19.5 lb-ft)
(C) : 33.3 ~ 41.2 N.m (3.4 ~ 4.2 kgf.m, 24.6 ~ 30.4 lb-ft)
(4Door, 5Door)

(2Door)
4.
Grease the pivot portions of the hinges indicated.
5.
Check for water leaks.
Components
1. Front door inside handle cap 2. Front door pull handle cap 3. Front door trim 4. Front door panel 5. Front door side impact pad 6. Front door quadrant inner cover 7 ...

Front Door Trim Component Location
(4Door, 5Door) 1. Front door trim (2Door) 1. Front door trim ...

See also:

Purge Control Solenoid Valve (PCSV) Description
Purge Control Solenoid Valve (PCSV) is installed on the intake manifold and controls the evaporative purge between the canister and the intake manifold. It is a normally closed solenoid valve ...

Front Door Belt Inside Weatherstrip Replacement
1. Remove the front door trim. (Refer to Front Door - "Front Door Trim") 2. Remove the front door belt inside weatherstrip (A ...

Starter Description
The starting system includes the battery, starter, solenoid switch, ignition switch, inhibitor switch (A/T), clutch pedal switch (M/T), ignition lock switch, connection wires and the battery ...

Categories

Copyright � www.kifomanual.com 2014-2026