Kia Forte: Cooling Fan Description
Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Engine Mechanical System / Cooling System / Cooling Fan Description
[Air conditioning type]
The cooling fan operates in 2 stages (HIGH/LOW). The engine control module
(ECM) controls the cooling fan according to the coolant temperature, vehicle
speed and A/C operation.
[Cooling fan operation conditions]
| A/C switch |
A/C pressure [kgf/cm² G (psi G)] |
Vehicle speed [km/h (mph)] |
Coolant temperature [°C (°F)] |
Cooling fan speed |
| OFF |
ㅡ |
V < 45 (28) |
100 ~ 105 (212 ~ 221) |
LOW |
| 105 (221) or above |
HIGH |
|||
| 45 (28) ≤ V < 80 (49.7) |
100 ~ 105 (212 ~ 221) |
LOW |
||
| 105 (221) or above |
HIGH |
|||
| 80 (49.7) ≤ V |
105 (221) or above |
HIGH |
||
| ON |
P < 6 (85.3) |
All |
105 (221) or above |
HIGH |
| 6 (85.3) ≤ P < 12 (170.7) |
V < 45 (28) |
60 ~ 100 (140 ~ 212) |
LOW |
|
| 100 (212) or above |
HIGH |
|||
| 45 (28) ≤ V < 80 (49.7) |
95 ~ 100 (203 ~ 212) |
LOW |
||
| 100 (212) or above |
HIGH |
|||
| 80 (49.7) ≤ V |
105 (221) or above |
HIGH |
||
| 12 (170.7) ≤ P < 15.5 (120.5) |
V < 45 (28) |
-30 ~ 95 (-22 ~ 203) |
LOW |
|
| 95 (203) or above |
HIGH |
|||
| 45 (28) ≤ V < 80 (49.7) |
95 ~ 100 (203 ~ 212) |
LOW |
||
| 100 (212) or above |
HIGH |
|||
| 80 (49.7) ≤ V |
105 (221) or above |
HIGH |
||
| 15.5 (120.5) ≤ P |
All |
-30 (-22) or above |
HIGH |
[Non-Air conditioning type]
The cooling fan operates in 1 stages (HIGH). The engine control module
(ECM) controls the cooling fan according to the coolant temperature, vehicle
speed and A/C operation.
[Cooling fan operation conditions]
| A/C switch |
A/C pressure [kgf/cm² G (psi G)] |
Vehicle speed [km/h (mph)] |
Coolant temperature [°C (°F)] |
Cooling fan speed |
| OFF |
ㅡ |
V < 45 (28) |
100 ~ 105 (212 ~ 221) or above |
HIGH |
| 45 (28) ≤ V < 80 (49.7) |
100 ~ 105 (212 ~ 221) or above |
HIGH |
||
| 80 (49.7) ≤ V |
105 (221) or above |
HIGH |
Cooling Fan Components
1. Cooling fan
2. Fan motor
3. Cooling fan shroud
4. Resister
...
Cooling Fan Specifications
Item
Specification
Fan type
PULLER
Fan speed control
Resistor (HI-LOW-OFF)
Air flow rate [㎥/h (yd³/h)]
1,700 (2,22 ...
See also:
Fuel Pump Motor Removal
1.
Remove the fuel pump (Refer to “Fuel Pump” in this group).
2.
Disconnect the electric pump wiring connector (A) and the fuel
sender conn ...
Crankshaft Position Sensor (CKPS) Inspection
1.
Check signal waveform of CKPS and CMPS using a scan tool.
Specification:
Refer to “Waveform”
...
Installation
1.
Install in the reverse order of removal.
2.
Tighten the vacuum pump mounting bolts to the specified torque.
...
Copyright © www.kifomanual.com 2014-2025