Kia Forte: Instrument Cluster Inspection - Indicators And Gauges - Body Electrical System - Kia Forte TD 2014-2018 Service ManualKia Forte: Instrument Cluster Inspection

Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Body Electrical System / Indicators And Gauges / Instrument Cluster Inspection

1.
Check point (Warning indicator)
NO
Ref
Symbol
Color
Name
Signal Input
Signal Control
(Unit / Sensor)
Check Point
1

Green
Turn Left
C-CAN
BCM
1.
CAN line failure
2

Green
Turn Right
C-CAN
3

Green
Front Fog
C-CAN
BCM
1.
CAN line failure
4

Blue
High Beam
C-CAN
BCM
1.
CAN line failure
5

Green
Low Beam
Hardwire
BCM
1.
Wiring failure
6

Green
Hardwire
C-CAN
BCM
1.
Wiring failure
7

Green
Cruise
C-CAN
EMS
1.
CAN line failure
8

Green
SET
C-CAN
EMS
1.
CAN line failure
9

Red
Seat Belt
C-CAN
BCM
1.
CAN line failure
10

Red
Air Bag
C-CAN
ACU
1.
CAN line failure
11

Yellow
Trunk Open
C-CAN
BCM
1.
CAN line failure
12

Red
Door Open
C-CAN
BCM
1.
CAN line failure
13

Red
High Temperature
C-CAN
EMS
1.
CAN line failure
14

Yellow
Immobilizer
Hardwire
SMK
1.
Wiring failure
15

Yellow
ABS
C-CAN
ESC
1.
CAN line failure
16

Yellow
ESC
C-CAN
ESC
1.
CAN line failure
17

Yellow
ESC OFF
C-CAN
ESC
1.
CAN line failure
18

Yellow
TPMS
(Tread & Fail)
C-CAN
TPMS
1.
CAN line failure
19

Yellow
Fuel Low
Low fuel resistance
Fuel Sender
1.
Fuel sender failure
2.
Wiring failure
20

Red
Parking Brake
C-CAN
BCM & ABS
or
ESC
1.
CAN line failure
21

Yellow
Oil Pressure
Hardwire
Oil Pressure Sensor
1.
Wiring failure
22

Red
Battery Charge
Hardwire
Battery Sensor
1.
Wiring failure
23

Yellow
Check Engine
C-CAN
EMS
1.
CAN line failure
24

Yellow
Low Washer
Hardwire
Water Level Sensor
1.
Wiring failure
25

Green

Active ECO

Hardwire
ECO ON/OFF Switch
1.
Switch failure
2.
Wiring failure

Passive ECO

C-CAN
26

Red
EPS
C-CAN
EPS Unit
1.
EPS unit failure
2.
CAN line failure

2.
Check point (Gauge)
No.
Name
Signal Input
Signal Control
(Unit/Sensor)
Check Point
1
Speedometer
C-CAN
TCS, ABS
1.
CAN Line failure
2
Tachometer
C-CAN
EMS
1.
CAN Line failure
3
Cooling water temperature
C-CAN
EMS
1.
CAN Line failure
4
Fuel
Hardwire
Fuel sender
1.
Fuel sender failure
2.
Wiring failure

3.
Connector terminal check list
No.
Description
Input/Output
Communication
Check Point
Spec
Condition
A1
Alternator L output
Output
Hardwire
-
IGN switch ON
A2
DC 12V input
Input
Hardwire
-
IGN switch ON
A3
Aig Bag (+)
Input
Hardwire
9 ~ 16 V
IGN switch ON
A4
Rheostat up switch
Input
Hardwire
Below 2V
IGN switch ON
Rheostat up switch ON
A5
Rheostat down switch
Input
Hardwire
Below 2V
IGN switch ON
Rheostat down switch ON
A6
Oil pressure indicator
Input
Hardwire
Below 1.5V
IGN switch ON
Oil pressure switch ON
A7
Active ECO
Input
Hardwire
Below 1.5V
IGN switch ON
A8
Battery Charge
Input
Hardwire
Below 1.5V
IGN switch ON
Charge switch ON
A9
Low washer
Input
Hardwire
-
IGN switch ON
A10
Immobilizer indicator
Input
Hardwire/CAN
Below 1.5V
IGN switch ON
A11
Steering wheel
input
Hardwire
-
IGN switch ON
A12
Trip switch 1
Input
Hardwire
0.7 ~ 4.4 V
IGN switch ON
A13
Trip switch (-)
Ground
Hardwire
Below 1V
Switch ground input
A14
AT S output
Output
Hardwire
7 ~ 15 V
IGN switch ON
A15
Instrument Cluster Installation
1. Connect the cluster connector. 2. Install the cluster assembly. 3. Install the cluster facia panel. ...

Troubleshooting
Symptom Possible cause Remedy Tachometer does not operate Cluster fuse (10A) blown Check for short and replace fuse CAN line faulty ...

See also:

Component Location
1. Hood switch 2. Burglar horn 3. BCM and RF antenna 4. Key warning switch 5. Front door switch 6. Front door lock actuator & switch 7. Rear door lock actuator &am ...

Heater & A/C Control Unit (Manual) Components
Connector Pin Function Connector No. Description Connector No. Description A 1 Ground B 14 In ...

Variable Intake Solenoid (VIS) Valve Specification
Item Specification Coil resistance (Ω) 30.0 ~ 35.0 [20°C(68°F)] ...

Copyright © www.kifomanual.com 2014-2024